crushing strength

Pressure Test in Rock Chambers DISCUSSION ON RADIAL CRUSHING STRENGTH TESTING

论压溃强度试验

Evaluation of Uncertainty in Measurement Crushing Strength Test of Cements Determination

水泥胶砂抗压强度试验测量不确定度评定

Study on Radial Crushing Strength of Ceramic-lined Steel Composite Pipe

陶瓷内衬复合钢管径向压溃强度分析

Shaped insulating refractory products & Determination of cold crushing strength

GB/T3997.2-1998定形隔热耐火制品常温耐压强度试验方法

Test method for crushing strength of vitrified pipe

GB/T2832-1996陶管抗外压强度试验方法

Sintered metal bushes & Determination of radial crushing strength

GB/T6804-1986烧结金属衬套径向压溃强度测定法

Crushing strength at elastic limit Research of Elastic Modulus of Mould Pressing Bamboo Processing Fragment Plate

弹性极限的抗压强度竹加工碎料模压代木板材的弹性模量研究

The porosity , bulk density and cold crushing strength of the refractory samples were determined .

讨论了气孔率、体积密度和常温耐压强度与电熔氧化镁加入量之间的关系。

Ben-ding strength of ice sheet is far less than its crushing strength .

冰的挠曲强度远小于其挤压强度。

EFFECT OF BOHAI ICE CRUSHING STRENGTH ON VERTICAL STRUCTURES Peak Ice Force in Ice Crushing on Vertical Structure

渤海海冰对直桩柱的作用力冰与直立结构挤压破坏时的极值静冰力

The bulk crushing strength and Abrasion strength are evidently different with the category of activated carbon .

测定了原粒度活性炭的堆积压碎强度和磨耗强度。

Crushing strength at elastic limit

弹性极限的抗压强度

Crushing strength at elastic limit The Conflict of Attack and Defence System Between TBM and ATBM

弹性极限的抗压强度地地弹道导弹武器系统攻防体系对抗

After the heat treatment process . the radial crushing strength of the samples are added alloy elements will not have much change .

热处理后，复合添加合金元素的试样径向压溃强度值变化不是很大。

The radial crushing strength of the samples are added Cr. Mo is the lowest .

添加Cr、Co元素试样的径向压溃强度低。

Determination of granula average crushing strength for monoammonium phosphate and diammonium phosphate

GB/T10212-1988磷酸一铵、磷酸二铵颗粒平均抗压强度测定

The influence of green ball quality and palletizing crushing strength are studied by using different size distribution of DAYE concentrate .

研究了不同的粒度组成大冶铁精矿对生球质量与成品球团抗压强度的影响。

Reinforcing ring is used to improve the anti - crushing strength of the pipeline and barrel - shaped equipment .

采取加强圈的措施来提高管线和桶体设备的抗外压强度。

For extrudates there are side crushing strength tests , bulk crushing strength tests , abrasion tests .

对挤条产品有侧压强度的测试，堆积强度测试和耐磨测试。

The insulation oil has low viscosity , low freezing point , high flashing point , high crushing strength and stability excellent features .

具有粘度小、凝固点低、闪点高、耐压强度大及稳定性好等优良特性。

The physical properties of catalysts such as specific surface area , pore volume , stacking density and crushing strength were tested .

测定了催化剂的比表面积、比孔体积、堆积密度和压碎强度等物理性质参数。

Influence preparation of parameters on crushing strength of the support for residue oil hydrodemetalation catalysts was investigated through experiments .

本文通过实验，探讨了制备条件对渣油加氢脱金属催化剂载体机械强度的影响。

Crushing strength , bending strength , bulk density , thermal shock resistance and heat expansion coefficient ofthe samples prepared were tested .

为了比较2种制品，分别对其进行了抗压强度、抗折强度、热膨胀系数、热震稳定性测试及微观形貌观察。

Meanwhile , pointing out that we should make static load experiment on the pile foundation for determination of single pile maximum crushing strength .

并提出对该型桩基础应做静荷载试验，确定单桩竖向抗压极限承载力。

The stalk crushing strength reduced with the increased densities , but with a rise of section decrease amplitude decreases . 4 .

茎杆表皮穿刺强度随着密度的增加而减小但随着节位的上升减小的幅度变小。

Experiments showed that the former had a higher crushing strength than that of the latter under the same preheating and roasting parameters .

试验表明，在同样的预热、焙烧的工艺参数下，用润磨原料生产的球团矿，其抗压强度高于未润磨原料生产的球团矿；

The application results showed that these two catalysts exhibited excellent activity and high crushing strength . The performance has reached the advanced level of the same products abroad .

结果表明：这两种催化剂活性好、强度高，性能达到国外同类产品的先进水平。

At 240 ~ 600 ℃, silicone resin decomposed , which leaded to the mass loss and loose structure and low cold crushing strength .

热处理温度为240~600℃时，有机硅树脂裂解产生质量损失，使试样内部结构松散，显气孔率显著增大，常温耐压强度较低；

The industry operation results show that RJW-3 catalyst possess high catalytic activity , good aromatic hydrocarbon saturation performance , low cracking activity and high crushing strength .

工业运转结果表明，该催化剂具有较高的催化活性和芳烃饱和能力、较低的裂解活性和较高的机械强度。

In selecting a refractory for a particular use , we should consider the texture , the crushing strength , and the chemical composition of the material .

为特定用途选择耐火材料时，要考虑其质地、抗碎强度和成分。